Wall Mount Drying Rack, 39 Points, 790 × 580 mm
- Wall mount laboratory drying rack for glassware drying
- Coated wire construction for routine laboratory use
- Includes 39 drying points
- Suitable for drying test tubes, boiling tubes, conical flasks and beakers
- Approximate rack size listed as 790 × 580 mm
- 790 mm measurement includes the attachment hooks
- Mounting point distance listed as 500 mm horizontally
- Mounting point distance listed as 780 mm vertically
- Weight listed as 2.5 kg
- Helps organise washed laboratory glassware during drying
- Designed for wall mounting in suitable laboratory areas
- Use under appropriate laboratory or educational supervision
AUD 136.90 (Ex GST)
Warming Coil Septa Support Adapter, BORO 3.3 Glass - Each
- Warming coil septa support adapter for laboratory glassware setups.
- Made from BORO 3.3 glass for chemical and thermal resistance.
- Supports controlled heating or warming around compatible assemblies.
- Septa support design allows use with suitable sampling or sealing points.
- Clear glass construction supports visual inspection during operation.
- Suitable for chemistry, research and teaching laboratory applications.
AUD 9.90 (Ex GST)
Watch Glasses, Soda Lime Glass, Laboratory Evaporation Cover Plates
- Manufactured from high quality soda lime glass for routine laboratory use
- Smooth, flat surface ideal for evaporation, sample observation, and small volume handling
- Commonly used as cover plates for beakers to reduce contamination and splashing
- Suitable for weighing solids, drying samples, and general laboratory handling
- Clear glass provides good visibility of samples during experiments
- Widely used in schools, universities, and routine laboratory applications
- Reliable laboratory-grade quality supplied by LabChoice Australia
From AUD 10.99 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Water Bath Temperature Controller for Hot Plate
- Thermostat control for compatible IEC water bath and hot plate setup
- Fits to the edge of the IEC water bath
- Controls the hot plate to help hold water temperature constant
- Thermostat element slides down into the inner corner of the bath
- Probe can remain submerged when only a small water volume is used
- Suitable for wet water bath temperature control
- Can also support dry bath operation where the method is suitable
- For dry use, probe should press against the inside face of the metal bath
- Provides better regulation than manual hot plate adjustment
- Purchased separately from the IEC water bath
AUD 236.90 (Ex GST)
Water Turbine Hydro-Electric Power Demo Spare Belt
- Replacement belt for water turbine hydro-electric power demo
- Suitable for LC-80-EM1639-01 demonstration apparatus
- Supports continued operation of classroom hydro-electric experiments
- Approximate belt diameter is 70 mm
- Spare belt only, main demonstration unit not included
- Useful for routine maintenance or belt replacement
- For laboratory or educational use under appropriate supervision
AUD 11.50 (Ex GST)
Water Turbine Hydro-Electric Power Educational Model
- Demonstrates hydro-electric power generation in classroom experiments
- Shows energy conversion from moving water to electrical output
- Suitable for renewable energy and sustainability lessons
- Helps teachers explain turbine-driven electricity generation
- Supports hands-on physics and environmental science activities
- Useful for group demonstrations and student observation
- For laboratory or educational use under appropriate supervision
AUD 216.90 (Ex GST)
Wave Demonstration Spring, Plastic Model for Physics
- Plastic spring for wave demonstration activities
- Lightweight design as listed
- Highly visible spring for classroom use
- Demonstrates waves in mid-air as listed
- Expands from 50 cm to 370 cm as listed
- Useful for transverse and longitudinal wave demonstrations
- Supports teaching of compression, rarefaction and wave motion
- Suitable for physics and general science practicals
- Practical for teacher-led classroom demonstrations
- Made from plastic as listed
- Keep clear of faces and eyes during stretching or release
- Use under appropriate laboratory or educational supervision
AUD 27.50 (Ex GST)
Weighing Measuring Scoop, BORO 3.3 Glass
- BORO 3.3 borosilicate glass weighing and measuring scoop for precise lab handling
- Suitable for transferring powders, crystals, and small solid samples
- Clear glass design allows easy visibility of sample quantity during use
- Good chemical resistance for routine laboratory weighing and preparation tasks
- Smooth formed surface helps with clean transfer and easy cleaning
- Reusable glass scoop for schools, universities, research, and industrial labs
- Ideal for sample prep, reagent handling, and general bench work in Australian laboratories
From AUD 14.90 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Whirling Sound Pipe for Sound Resonance Experiments
- Whirling sound pipe for physics and sound demonstrations
- Demonstrates resonance as listed
- Can also be used to demonstrate fluid dynamics
- Produces up to 5 possible frequencies as listed
- Approximate length listed as 73 cm
- Pipe diameter listed as 32 mm
- Weight listed as about 45 g per piece
- Made from PE as listed
- Lightweight design for classroom demonstrations
- Useful for sound, vibration and air-flow studies
- Keep clear of people and objects while whirling
- Use under appropriate laboratory or educational supervision
AUD 11.50 (Ex GST)
Wide Range Specific Gravity Hydrometers, 250 mm
- Wide range specific gravity hydrometers for laboratory use
- Brand listed as Brannan, U.K.
- Specific Gravity Hydrometer 200 Series as listed
- Overall length listed as 250 mm
- Scale basis listed as specific gravity 60/60°F
- Each instrument covers a 0.200 S60/60°F span as listed
- Accuracy listed as 0.004 S60/60°F
- Divisions listed as 0.002 S60/60°F
- Made from soda glass as listed
- Steel shot ballast and synthetic wax resin construction as listed
- Supplied with protective plastic tube as listed
- Use under appropriate laboratory or educational supervision
From AUD 78.50 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Wimshurst Machine for Electrostatic Charge
- Demonstrates electrostatic charge generation, storage and visible discharge for physics education.
- Hand crank rotates twin plates in opposite directions to build static electricity.
- Leyden jar capacitors store charge before spark discharge between terminals.
- Mounted on a wooden base with rubber feet for stable classroom use.
- Compact demonstration size with 300 × 180 mm base and 300 mm height.
- Suitable for supervised lessons on electrostatics, induction, capacitance and electrical discharge, as students observe charge separation and transfer safely during guided classroom experiments.
AUD 174.50 (Ex GST)
Wimshurst Machine Spare Belts, Replacement Belt Set
- Replacement belts for compatible Wimshurst machine demonstrations
- Suitable for LC-80-EM1641-01 Wimshurst machine
- Used to support plate rotation during electrostatics experiments
- Approximate belt circumference is 45 cm
- Suitable for approximately 140 mm diameter belt path
- Available as spare belt only or spare belt pair
- For laboratory or educational use under appropriate supervision
From AUD 12.50 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Wine and Beer Hydrometer, 230 mm
- Hydrometer for wine and beer making applications
- Measures specific gravity of compatible wine and beer samples
- Length listed as 230 mm
- Designed for monitoring the fermentation process
- Zoned scale supports easy reading during home brew testing
- Adjusted at 20°C
- Useful for estimating fermentation progress and potential alcohol changes
- Suitable for home brewing, teaching and basic laboratory demonstrations
- Confirm sample temperature, cylinder size and reading method before use
- Handle carefully to avoid glass breakage
AUD 43.90 (Ex GST)
Wireless Power Transfer Experiment Kit
- Wireless power transfer experiment kit for demonstrating the mechanism of wireless charging
- Helps explain the wireless charging principle used in smartphones and similar devices
- Includes small LED devices with built-in receiving coils
- Includes a flat coil for wireless power transfer
- USB power adapter is supplied for powering the transfer coil
- Demonstrates power transfer without direct wired connection between the LED device and flat coil
- LED devices light up when placed at the centre of the powered flat coil
- Suitable for classroom demonstrations, science learning and laboratory teaching workflows
- Supports practical understanding of coil-based power transfer and wireless energy transmission
- Placement, USB power connection and demonstration setup should be confirmed before use
AUD 162.00 (Ex GST)
Wooden Double Burette Stand
- Double burette stand for holding two burettes during titration work
- Wooden construction provides stable bench support for routine laboratory use
- Nylon thumb screws support firm, adjustable clamping without direct metal contact
- Suitable for burettes down to 10 mm diameter as specified
- Supports side-by-side burette positioning for comparative or repeated trials
- Helps maintain vertical alignment for clearer meniscus reading
- Suitable for laboratory and educational use under appropriate supervision
AUD 41.50 (Ex GST)
Wooden Funnel Holder on Stand, Single or Double Place
- Wooden funnel holder on stand for supporting compatible laboratory funnels
- Available in single-place and double-place configurations
- Varnished wooden construction supports routine laboratory and classroom use
- Single funnel holder includes clamping screw for practical height adjustment
- Single-place base size is stated as 200 × 110 mm with 460 mm rod height
- Double-place base size is stated as approximately 290 × 110 mm with 460 mm rod height
- Suitable for filtration, liquid transfer, sample preparation and teaching practicals
From AUD 34.90 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Wooden Hollow Sonometer, 1 m, Mersenne’s Law
- Wooden hollow sonometer for sound and vibration demonstrations
- Length listed as 1 m
- Designed for demonstrating Mersenne’s law
- Shows the relationship between string frequency, tension, length and mass per unit length
- Suitable for plucked string sound experiments
- Useful for teaching pitch, frequency, resonance and wave behaviour
- Hollow wooden body supports classroom sound demonstration work
- Suitable for physics laboratories and educational settings
- Spare set of wires available separately under LC-80-PA1369-01
- Use under appropriate laboratory or educational supervision
AUD 120.90 (Ex GST)
Wooden Lab Disposable Stirrer - 114 x 10 x 2 mm
- Wooden disposable lab stirrers for quick manual mixing and sample handling
- Single use design helps reduce cross contamination between tests
- Lightweight and easy to handle for routine laboratory tasks
- Suitable for stirring, transferring, and blending small volumes
- Convenient option for schools, training labs, and general bench work
- Simple, cost effective consumable for day to day laboratory use
- Easy to store and dispense for fast workflow during repeated testing
- Ideal for non corrosive, low temperature applications where disposable tools are preferred
From AUD 19.90 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Wooden Swab Sticks, Pack of 100 Pcs
- Wooden swab sticks for laboratory and educational use
- Supplied as pack of 100 pieces as listed
- Wooden stick construction as listed
- Useful for routine sample handling and application tasks
- Suitable for compatible laboratory, classroom and preparation workflows
- Can be used for spreading, applying or collecting compatible materials
- Practical disposable format for controlled single-use procedures
- Helps reduce cross-contamination when used once and discarded
- Sterility status is not specified
- Confirm swab tip material and dimensions before ordering
- Not for medical or diagnostic use unless specified
- Use under appropriate laboratory or educational supervision
Wooden Test Tube Rack with Pegs for Test Tube Storage
- Wooden test tube rack for laboratory and educational use
- Designed to hold compatible 25 mm diameter tubes
- Includes 6 × 25 mm holes as listed
- Supplied with pegs as listed
- Wooden rack construction
- Approximate size listed as 200 mm × 90 mm high
- Suitable for holding and drying test tubes
- Useful for school, university and teaching laboratories
- Practical bench-top rack for routine tube organisation
- Confirm tube diameter and fit before use
- Keep away from open flame and excessive heat
- Use under appropriate laboratory or educational supervision
AUD 19.50 (Ex GST)
Wooden V-Groove Lens and Mirror Holders, 50 mm and 75 mm
- Wooden lens and mirror holder range for classroom optics experiments
- Available for 50 mm diameter and 75 mm diameter lenses or mirrors
- V-shaped slot supports simple positioning of compatible optics
- Rectangular base provides practical bench support during use
- Suitable for holding lenses and mirrors in teaching demonstrations
- Useful for reflection, refraction and image formation activities
- Simple design supports student practical work and classroom setup
- Confirm lens or mirror diameter, thickness and fit before use
From AUD 6.90 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Zoological Animal Cell Inflatable Ball Model
- Inflatable animal cell teaching model for biology education
- Designed for zoology, cell biology and general science lessons
- Useful for teaching basic animal cell structure
- Inflatable ball format supports visual classroom demonstration
- Practical teaching aid for student observation and revision
- Suitable for school, university and teaching laboratory use
- Can be used alongside diagrams, worksheets and approved curriculum resources
- Helps introduce cell structure, organelles and animal cell organisation
- Confirm model size, printed labels and included pump before ordering
- Intended for laboratory or educational settings only
- Use under appropriate teacher or laboratory supervision
AUD 33.90 (Ex GST)
Zoological Animal Cell Model on Stand
- Zoological animal cell teaching model for biology education
- Mounted on stand for classroom display
- Designed for cell biology, zoology and general science lessons
- Shows animal cell structure in a visual model format
- Useful for teaching organelles and basic cell organisation
- Dimension listed as 165 × 123 × 180 mm
- Practical visual aid for classroom demonstration and revision
- Suitable for school, university and teaching laboratory use
- Can be used alongside diagrams, worksheets and microscope activities
- Intended for laboratory or educational settings only
- Use under appropriate teacher or laboratory supervision
AUD 199.50 (Ex GST)
Zoological Earthworm Dissection Model on Board
- Zoological earthworm dissection teaching model
- Mounted on board or base for classroom display
- Shows external character in one portion
- Remaining section shows dissected internal anatomy
- Displays important systems including nervous system
- Shows digestive, circulatory and reproductive organs
- Numbered model supports structured identification
- Supplied with English key card
- Useful for zoology, biology and comparative anatomy lessons
- Suitable for school, university and teaching laboratory use
- Intended for laboratory or educational settings only
- Use under appropriate teacher or laboratory supervision
AUD 115.90 (Ex GST)
Zoological Fish Dissection Model on Stand
- Zoological fish dissection teaching model
- Mounted on stand for classroom display
- Designed for biology, zoology and anatomy education
- Useful for teaching fish internal anatomy
- Supports classroom explanation without fresh specimen dissection
- Practical visual aid for dissection preparation and revision
- Suitable for school, university and teaching laboratory use
- Can be used alongside diagrams, worksheets and approved curriculum resources
- Confirm model size, labelled parts and material before ordering
- Intended for laboratory or educational settings only
- Use under appropriate teacher or laboratory supervision
AUD 180.90 (Ex GST)
Zoological Frog Dissection Model on Board
- Zoological frog dissection teaching model
- Mounted on board for classroom display
- Designed for biology, zoology and anatomy education
- Useful for teaching frog internal anatomy
- Supports classroom explanation without fresh specimen dissection
- Practical visual aid for dissection preparation and revision
- Suitable for school, university and teaching laboratory use
- Can be used alongside diagrams, worksheets and approved curriculum resources
- Confirm model size, labelled parts and material before ordering
- Intended for laboratory or educational settings only
- Use under appropriate teacher or laboratory supervision
AUD 186.90 (Ex GST)
didn't see what you are looking for ?
We’ll source it or make it for you. LabChoice supports your research every step.