Viscometer, U-Tube Reverse Flow, BS/IP/RF, BORO 3.3 Glass
- Reverse flow U-tube BS/IP/RF viscometers for laboratory use
- Supplied without constant certificate
- Made from 3.3 borosilicate glass
- Autoclavable glass construction
- Suitable for viscosity and flow time experiments
- Available in sizes 2, 3, 4, 5, 6, 7, 8, 9, 10 and 11
- Listed viscosity ranges from 2 to 300,000 mm²/sec
- Supplied as 1 piece per pack
- Useful for laboratory, student and training applications
- Handle carefully as precision laboratory glassware
- Confirm size, viscosity range and method requirements before ordering
- Use under appropriate laboratory or educational supervision
Viscometer, Ubbelohde Type 501-20 II, 10–100 mm²/s, Calibrated BORO 3.3 Glass
- Ubbelohde type capillary viscometer for manual viscosity measurement
- Model listed as SI Analytics Ubbelohde 501-20 II
- Measured range listed as 10 to 100 mm²/s
- Maximum measured value listed as 100 mm²/s
- Minimum measured value listed as 10 mm²/s
- Viscometer constant listed as 0.1
- Capillary number listed as II
- Internal diameter listed as 1.13 mm
- Capacity listed as 15 to 20 mL
- Overall length listed as 290 mm
- Standards listed as ISO 3105 and DIN 51562
- Supplied as the selected calibrated viscometer only
Visking Dialysis Tubing, Laboratory Membrane Tubing for Diffusion Work
- Visking dialysis tubing for diffusion and osmosis demonstration work
- Made from seamless regenerated cellulose membrane material
- Supplied in practical 5 metre roll format
- Supports teaching of permeability, equilibrium, gradients, and plasmolysis
- Two size formats allow selection by supplied tubing dimensions
From AUD 134.50 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Volatile Matter Determination Crucibles and Lids, Translucent Fused Silica
- Fused silica crucibles and lids designed for volatile matter determination in coal and coke analysis
- Manufactured by Infusil for laboratory heating and analytical applications
- Referenced to B.S. 1016 (Part 1) for volatile matter testing
- Translucent fused silica construction for high-temperature laboratory use
- Transparent fused quartz versions available on enquiry
- Crucibles available with or without projection
- Crucible external height of 38 mm and diameter of 25 mm
- Matching lids with a height of 3–4.75 mm and diameter of 21 mm
- Designed for controlled heating of solid samples in laboratory furnaces
- Crucibles and lids available separately or as a set
- Suitable for coal testing, fuel analysis, research and industrial quality control laboratories
From AUD 39.50 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Volumetric Flask with PE Stopper, Class A, Borosilicate Glass (BORO 3.3)
- Class A tolerance for precision measurements
- Leak-resistant PE stopper ensures secure sealing
- Narrow neck design improves volumetric accuracy
- Used in titration, education, and research labs
- Preferred by professionals across Australia
- Made from LabChoice BORO 3.3 glass – High quality
From AUD 9.50 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Volumetric Flask with PE Stopper, Class B, Borosilicate Glass (BORO 3.3)
- Class B tolerance suitable for general lab use
- Leak-proof PE stopper provides secure closure
- Narrow neck ensures better volume control
- Used in school labs, research, and QC testing
- Preferred for everyday solution preparation
- Made from LabChoice BORO 3.3 glass – High quality
From AUD 6.90 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Volumetric Transfer Pipette, Class A, BORO 3.3
- Class A volumetric transfer pipette for precise fixed-volume liquid transfer
- Made from BORO 3.3 borosilicate glass for chemical and thermal resistance
- Designed for accurate measuring and dispensing in analytical laboratory work
- Suitable for education, research, quality control, and routine lab applications
- Clear calibration mark supports reliable volume reading and repeatable results
From AUD 5.90 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Vortex Mixer, Fixed Speed 3000 rpm Laboratory Mixing Type
- 3,000rpm for shaking to rapid mixing of samples
- Touch or continuous operation mode
- Includes a standard top head for mixing a single test tube or other small vessel up to 30mm in diameter
- Electronic speed control maintains constant speed even during changes in load
- Steel base with specially designed vacuum suction feet provides stability and dampens vibration
- Robust aluminum-cast construction
AUD 350.50 (Ex GST)
Save 30%
Vortex Mixer, Portable Laboratory Mixing Type up to 3000 rpm
- Compact , portable and fits nicelyon bench-top (erase desktops and table tops)
- Touch operation,Fixed speed of 3,000rpm for rapid mixing of samples
- Powerful and efficient 12V DC brushless motor is smooth operation and has long life
- Foot pad design secures the mixer in place and does not wobble during operation
AUD 225.00 (Ex GST)
Save 27%
Vortex Mixer, Variable Speed Laboratory Mixing Type up to 3000 rpm
- Variable speed of 0 to 3,000rpm for gentle shaking to rapid mixing of samples
- Touch or continuous operation mode
- Includes a standard top head for mixing a single test tube or other small vessel up to 30mm in diameter
- Electronic speed control maintains constant speed even during changes in load
- Steel base with specially designed vacuum suction feet provides stability and dampens vibration
- Robust aluminum-cast construction
AUD 275.50 (Ex GST)
Wall Mount Drying Rack, 39 Points, 790 × 580 mm
- Wall mount laboratory drying rack for glassware drying
- Coated wire construction for routine laboratory use
- Includes 39 drying points
- Suitable for drying test tubes, boiling tubes, conical flasks and beakers
- Approximate rack size listed as 790 × 580 mm
- 790 mm measurement includes the attachment hooks
- Mounting point distance listed as 500 mm horizontally
- Mounting point distance listed as 780 mm vertically
- Weight listed as 2.5 kg
- Helps organise washed laboratory glassware during drying
- Designed for wall mounting in suitable laboratory areas
- Use under appropriate laboratory or educational supervision
AUD 136.90 (Ex GST)
Warming Coil Adapter B24 Joint BORO 3.3 Glass Laboratory Grade
- Designed for gentle heating and temperature control in glassware setups
- Compatible with B24 standard joints for secure connections
- Facilitates even heat distribution during distillation or reaction processes
- Ideal for maintaining sample temperature and preventing condensation
- Made from durable, heat-resistant BORO 3.3 borosilicate glass
- Expertly manufactured and quality-tested by LabChoice Australia
AUD 89.90 (Ex GST)
Warming Coil Septa Support Adapter, BORO 3.3 Glass - Each
- Warming coil septa support adapter for laboratory glassware setups.
- Made from BORO 3.3 glass for chemical and thermal resistance.
- Supports controlled heating or warming around compatible assemblies.
- Septa support design allows use with suitable sampling or sealing points.
- Clear glass construction supports visual inspection during operation.
- Suitable for chemistry, research and teaching laboratory applications.
AUD 9.90 (Ex GST)
Warming Trays
- Warming trays for controlled heating of laboratory samples and vessels
- Suitable for gentle warming across a flat heated surface
- Supports use with bottles, containers, glassware, and lab items
- Practical benchtop format for routine laboratory workflows
- Suitable for research, education, and general laboratory applications
From AUD 1,254.00 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Wash Bottle with Fixed Straw, Leakproof, Material LDPE, High Quality - Each
- Fixed straw allows steady, upright dispensing
- Leakproof screw cap prevents accidental spills
- Flexible LDPE body for easy squeeze control
- Clear volume markings for accurate dispensing
- Ideal for solvents, distilled water, and lab rinsing
- Supplied by LabChoice Australia – Reliable quality
From AUD 2.70 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Wash Bottle with Flexible Straw, Leakproof, Material LDPE, High Quality - Each
- Flexible straw enables precise directional dispensing
- Leakproof cap prevents spills and contamination
- Soft LDPE body allows easy squeeze action
- Graduated for controlled volume use
- Suitable for rinsing, dispensing solvents, or water
- Supplied by LabChoice Australia – Reliable quality
From AUD 2.30 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Washable Adhesive Work Mat
- 60 x 60 mm and 332 x 166 mm sizes suit varied bench setups
- Double-sided adhesive supports placement on clean, dry, flat surfaces
- Helps keep containers, glassware and flat-bottomed flasks in place
- Washable surface can be wiped clean with a damp cloth to restore tack
- Reusable thousands of times for repeated laboratory holding support
- Can be trimmed to size for benches, trolleys and preparation areas
Watch Glasses, Soda Lime Glass, Laboratory Evaporation Cover Plates
- Manufactured from high quality soda lime glass for routine laboratory use
- Smooth, flat surface ideal for evaporation, sample observation, and small volume handling
- Commonly used as cover plates for beakers to reduce contamination and splashing
- Suitable for weighing solids, drying samples, and general laboratory handling
- Clear glass provides good visibility of samples during experiments
- Widely used in schools, universities, and routine laboratory applications
- Reliable laboratory-grade quality supplied by LabChoice Australia
From AUD 10.99 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Water Bath Temperature Controller for Hot Plate
- Thermostat control for compatible IEC water bath and hot plate setup
- Fits to the edge of the IEC water bath
- Controls the hot plate to help hold water temperature constant
- Thermostat element slides down into the inner corner of the bath
- Probe can remain submerged when only a small water volume is used
- Suitable for wet water bath temperature control
- Can also support dry bath operation where the method is suitable
- For dry use, probe should press against the inside face of the metal bath
- Provides better regulation than manual hot plate adjustment
- Purchased separately from the IEC water bath
AUD 236.90 (Ex GST)
Water Hardness Test Paper Strips, Pack of 50
- Water hardness test strips for laboratory and educational use
- Supplied as pack of 50 strips as listed
- Measures water hardness due to calcium carbonate as listed
- Calibrated at 0, 50, 125, 250 and 500 ppm
- Also calibrated at 0, 3, 7, 15 and 30 grains per gallon
- Helps indicate whether water is soft or hard
- Provides results in seconds as listed
- Suitable for routine water-quality demonstrations
- Useful for science classrooms and general water testing activities
- Intended for approximate screening rather than certified analysis
- Confirm colour chart and test instructions before use
- Use under appropriate laboratory or educational supervision
AUD 59.90 (Ex GST)
Water Turbine Hydro-Electric Power Demo Spare Belt
- Replacement belt for water turbine hydro-electric power demo
- Suitable for LC-80-EM1639-01 demonstration apparatus
- Supports continued operation of classroom hydro-electric experiments
- Approximate belt diameter is 70 mm
- Spare belt only, main demonstration unit not included
- Useful for routine maintenance or belt replacement
- For laboratory or educational use under appropriate supervision
AUD 11.50 (Ex GST)
Water Turbine Hydro-Electric Power Educational Model
- Demonstrates hydro-electric power generation in classroom experiments
- Shows energy conversion from moving water to electrical output
- Suitable for renewable energy and sustainability lessons
- Helps teachers explain turbine-driven electricity generation
- Supports hands-on physics and environmental science activities
- Useful for group demonstrations and student observation
- For laboratory or educational use under appropriate supervision
AUD 216.90 (Ex GST)
Wave Demonstration Spring, Plastic Model for Physics
- Plastic spring for wave demonstration activities
- Lightweight design as listed
- Highly visible spring for classroom use
- Demonstrates waves in mid-air as listed
- Expands from 50 cm to 370 cm as listed
- Useful for transverse and longitudinal wave demonstrations
- Supports teaching of compression, rarefaction and wave motion
- Suitable for physics and general science practicals
- Practical for teacher-led classroom demonstrations
- Made from plastic as listed
- Keep clear of faces and eyes during stretching or release
- Use under appropriate laboratory or educational supervision
AUD 27.50 (Ex GST)
Weighing Measuring Scoop, BORO 3.3 Glass
- BORO 3.3 borosilicate glass weighing and measuring scoop for precise lab handling
- Suitable for transferring powders, crystals, and small solid samples
- Clear glass design allows easy visibility of sample quantity during use
- Good chemical resistance for routine laboratory weighing and preparation tasks
- Smooth formed surface helps with clean transfer and easy cleaning
- Reusable glass scoop for schools, universities, research, and industrial labs
- Ideal for sample prep, reagent handling, and general bench work in Australian laboratories
From AUD 14.90 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
West Condenser BORO 3.3 for Efficient Reflux Cooling
- Designed for efficient vapour cooling in reflux and distillation setups
- Straight-tube inner path with narrow cooling jacket for stable heat exchange
- Made from BORO 3.3 glass compliant with ISO 3585 and ASTM E438 Type I, Class A
- High resistance to thermal shock, acids and organic solvents
- Smooth vapour flow and reliable condensate return for reproducible reactions
- Interchangeable ground glass joints for seamless compatibility with standard labware
From AUD 44.90 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Whirling Sound Pipe for Sound Resonance Experiments
- Whirling sound pipe for physics and sound demonstrations
- Demonstrates resonance as listed
- Can also be used to demonstrate fluid dynamics
- Produces up to 5 possible frequencies as listed
- Approximate length listed as 73 cm
- Pipe diameter listed as 32 mm
- Weight listed as about 45 g per piece
- Made from PE as listed
- Lightweight design for classroom demonstrations
- Useful for sound, vibration and air-flow studies
- Keep clear of people and objects while whirling
- Use under appropriate laboratory or educational supervision
AUD 11.50 (Ex GST)
Wide Range Specific Gravity Hydrometers, 250 mm
- Wide range specific gravity hydrometers for laboratory use
- Brand listed as Brannan, U.K.
- Specific Gravity Hydrometer 200 Series as listed
- Overall length listed as 250 mm
- Scale basis listed as specific gravity 60/60°F
- Each instrument covers a 0.200 S60/60°F span as listed
- Accuracy listed as 0.004 S60/60°F
- Divisions listed as 0.002 S60/60°F
- Made from soda glass as listed
- Steel shot ballast and synthetic wax resin construction as listed
- Supplied with protective plastic tube as listed
- Use under appropriate laboratory or educational supervision
From AUD 78.50 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Wilson’s Cloud Chamber, Expansion Type, Without Sources
- Wilson’s cloud chamber for laboratory and educational demonstrations
- Classical expansion-type cloud chamber design
- Uses alcohol vapour and partial vacuum to create supersaturation
- Demonstrates visible tracks produced by ionising particles
- Designed for use with a suitable vacuum pump arrangement
- Reversed tyre pump or compatible vacuum source may be required
- Light source is required to illuminate the chamber
- Alpha pin source is required for alpha-particle track demonstrations
- Supplied without radioactive sources as listed
- Alcohol, lamp, pump and source should be confirmed before use
- Radiation source use must follow approved institutional procedures
- Use under appropriate laboratory or educational supervision
AUD 573.50 (Ex GST)
Wimshurst Machine for Electrostatic Charge
- Demonstrates electrostatic charge generation, storage and visible discharge for physics education.
- Hand crank rotates twin plates in opposite directions to build static electricity.
- Leyden jar capacitors store charge before spark discharge between terminals.
- Mounted on a wooden base with rubber feet for stable classroom use.
- Compact demonstration size with 300 × 180 mm base and 300 mm height.
- Suitable for supervised lessons on electrostatics, induction, capacitance and electrical discharge, as students observe charge separation and transfer safely during guided classroom experiments.
AUD 174.50 (Ex GST)
Wimshurst Machine Spare Belts, Replacement Belt Set
- Replacement belts for compatible Wimshurst machine demonstrations
- Suitable for LC-80-EM1641-01 Wimshurst machine
- Used to support plate rotation during electrostatics experiments
- Approximate belt circumference is 45 cm
- Suitable for approximately 140 mm diameter belt path
- Available as spare belt only or spare belt pair
- For laboratory or educational use under appropriate supervision
From AUD 12.50 (Ex GST)
This product has multiple variants. The options may be chosen on the product page
Wind Power Generator Renewable Energy Demonstration
- Wind power generator for laboratory and educational demonstrations
- Designed to demonstrate renewable energy conversion
- Shows how moving air can produce electrical current
- Operates in low wind conditions as listed
- Can be driven by airflow from a table fan as listed
- Useful for teaching wind energy and basic generator principles
- Supports STEM activities on energy transfer and sustainability
- Can be used to power a compatible motor or lamp as listed
- Suitable for classroom demonstrations and student investigations
- Confirm included accessories before ordering
- Keep fingers and loose items away from rotating blades
- Use under appropriate laboratory or educational supervision
AUD 216.90 (Ex GST)
Wind Vane and Speed Indicator, Classroom Environmental Science Demonstrator
- Demonstration wind vane for laboratory and educational use
- Used to show wind direction in classroom activities
- Product title references wind speed indicator / anemometer
- Supplied details describe wind direction reading by pointer
- Made from plastic as listed
- Overall size listed as 190 × 140 mm
- Base size listed as 90 × 90 mm
- North marking is aligned to face north before reading
- Pointer indicates wind direction during use
- Suitable for weather, air movement and environmental science lessons
- Confirm wind speed indicator function before ordering
- Use under appropriate laboratory or educational supervision
AUD 49.90 (Ex GST)
didn't see what you are looking for ?
We’ll source it or make it for you. LabChoice supports your research every step.