Low-Speed Clinical Centrifuge with Blood, Urine and Faecal Programs, up to 4,000 rpm
- Adjustable speed range from 300 to 4,000 rpm in 100 rpm increments, delivering up to 1,900 × g
- Default 8-place angle rotor accommodates 8 × 15 mL compatible centrifuge tubes
- Optional 12-place angle rotor supports 12 × 10 mL compatible laboratory tubes
- Blood, urine and faecal programs provide convenient settings for routine specimen processing
- Three acceleration levels and four deceleration levels support controlled starting and braking
- LED display allows operating speed to be selected and monitored in rpm or RCF
- Maintenance-free brushless DC motor supports quiet operation at ≤60 dB(A)
- Description
Description
The Low-Speed Clinical Centrifuge, also known as a benchtop specimen centrifuge, is designed for routine processing of blood, urine, faecal and general laboratory samples in clinical diagnostic, pathology, medical testing and biomedical research laboratories. Its compact design and selectable angle rotors support commonly used 10 mL and 15 mL laboratory tube formats.
The centrifuge provides an adjustable speed range from 300 to 4,000 rpm in 100 rpm increments and generates a maximum relative centrifugal force of 1,900 × g. Speed accuracy is specified at ±100 rpm. Operating speed can be selected and viewed in either rpm or RCF, allowing users to follow laboratory procedures written using rotational speed or centrifugal force.
The default angle rotor accommodates 8 × 15 mL compatible tubes, while an alternative angle rotor supports 12 × 10 mL tubes. The appropriate rotor and tube combination should be selected according to the specimen volume, tube dimensions, balance requirements and validated centrifugation method.
Three routine programs are provided for common clinical sample-processing workflows. The blood program operates at 3,200 rpm for 10 minutes, the urine program at 1,800 rpm for 5 minutes and the faecal program at 1,300 rpm for 10 minutes. These settings offer convenient starting parameters, but laboratories should confirm their suitability against tube manufacturer instructions, specimen requirements and internal procedures.
Run time can be set from 1 to 99 minutes, with HOLD mode available for continuous operation. Three acceleration levels and four deceleration levels allow the starting and stopping response to be adjusted according to the sample and separation requirement. Acceleration and braking times are specified at approximately 25 seconds and 35 seconds respectively.
The LED display provides clear visibility of the selected operating parameters. Automatic internal diagnosis and self-detection functions monitor instrument operation, while the maintenance-free brushless DC motor supports repeated routine use with a stated noise level of no more than 60 dB(A).
LabChoice Australia supplies this Low-Speed Clinical Centrifuge for clinical diagnostic laboratories, pathology laboratories, hospital laboratories, urinalysis laboratories, medical centres, biomedical research facilities, university teaching laboratories and general life-science laboratories. It is suitable for routine pre-analytical processing of compatible blood, urine, faecal and other laboratory samples using the correct rotor, balanced tube loading and validated centrifugation procedures.
| Specification | Details |
|---|---|
| Product type | Low speed centrifuge |
| Speed range | 300 to 4,000 rpm |
| Speed increment | 100 rpm |
| Maximum RCF | 1,900 x g |
| Speed accuracy | ±100 rpm |
| Rotor type | A12-10P and A8-15P |
| Rotor capacity | Angle 8 x 15 mL default and angle 12 x 10 mL |
| Run time | 1 to 99 minutes, HOLD |
| Display | LED |
| Safety devices | Automatic internal diagnosis |
| Additional safety | Automatic internal diagnosis and self-detection |
| Acceleration/Braking time | 25 seconds up, 35 seconds down |
| Acceleration/Deceleration control | 3 acceleration levels and 4 deceleration levels |
| Program settings | Blood 3200 rpm for 10 min, urine 1800 rpm for 5 min, faecal 1300 rpm for 10 min |
| Motor type | Brushless DC motor |
| Power | Single phase, 100 V to 240 V, 50 Hz/60 Hz |
| Dimensions | 286 x 367 x 227 mm |
| Weight | 9.2 kg |
| Noise level | ≤60 dB(A) |
Frequently Bought Together
Flat Rubber Sleeve For Digital Vortex Mixture
$12.50(Ex GST)
Digital Colony Counter, LED Display with Pressure Sensor and Ring Lamp
$1,707.90(Ex GST)
Glazed Gooch Filtration Crucibles
From $5.90 (Ex GST)
Hand Held Refractometers, Brix and Salinity ATC Measurement Type
From $99.90 (Ex GST)
Microplate Clamp for Digital Vortex Mixer
$44.50(Ex GST)
Kimtech Disposable Wipes, Delicate Lab Task Wipes
From $9.20 (Ex GST)
Test Tubes Round Bottom, Rimless, Heat Resistant, BORO 3.3 Glass
From $31.00 (Ex GST)
Similar Products
Block for Cuvettes
$392.00(Ex GST)
Block for Epp Tubes
From $255.00 (Ex GST)
Digital Dry Block Heater with Microprocessor Control, 200°C with LED Display
From $1,382.00 (Ex GST)
Flat Block for Vials
$254.00(Ex GST)
Humidity Measurement Instruments For Laboratory
From $12.50 (Ex GST)
Hybridisation Oven
$6,274.00(Ex GST)
Hybridisation Oven Carousel Suit
From $1,216.00 (Ex GST)
Laboratory Water Bath with Hot Plate
From $236.90 (Ex GST)
Medium Rotary Mixer
$3,333.00(Ex GST)
Micro Tray Block
From $308.00 (Ex GST)
Recirculating Cooler with Tank
$8,262.00(Ex GST)
Simmerstat Control with Combined Hot Plates & Magnetic Stirrer
From $835.90 (Ex GST)
Vernier Calipers For Laboratory and Educational Work
From $9.90 (Ex GST)
Vortex Mixer, up to 3000 rpm
From $542.00 (Ex GST)
[porto_related_products_slider]
FEATURED PRODUCTS
BEST SELLING PRODUCTS
Polypropylene Filter Funnels, Gravity Filtration Range
From $1.50 (Ex GST)
Glass Petri Dishes with Lid, Autoclavable, Borosilicate Glass (BORO 3.3)
From $3.90 (Ex GST)
What Our Customers Say
⭐⭐⭐⭐⭐
We ordered a set of customised BORO 3.3 borosilicate glassware for our teaching labs, and LabChoice Australia exceeded every expectation. From the first consultation to final delivery, their team listened carefully, offered expert advice, and ensured every piece matched our specifications perfectly.
The clarity and precision of the glassware are exceptional, and the quick turnaround made setup effortless. It’s refreshing to work with an Australian supplier who genuinely understands laboratory needs and takes pride in quality craftsmanship. We’ll definitely be returning to LabChoice for future glassware requirements
⭐⭐⭐⭐⭐
Our lab required high-precision BORO 3.3 glassware for analytical testing, and LabChoice Australia delivered outstanding results. The ordering process was simple, communication was clear, and every beaker and flask arrived perfectly calibrated and ready for use.
The quality of the glass is exceptional — resistant to heat, easy to clean, and consistently accurate in measurement. It’s reassuring to know there’s an Australian supplier that combines scientific precision with genuine customer care. I’d recommend LabChoice to any research team looking for dependable labware
⭐⭐⭐⭐⭐
We needed a set of customised borosilicate glassware for a specialised project, and LabChoice Australia delivered exactly what we envisioned. The team worked closely with us from design to production, ensuring every detail met our specifications. The craftsmanship is exceptional, and the turnaround time was impressive. It’s reassuring to know we can rely on them for unique, made-to-order pieces
⭐⭐⭐⭐⭐
LabChoice Australia has completely changed the way we source our lab glassware. The quality is consistently top-notch, and every piece meets the precision we need for reliable results. Their team knows their stuff, answers our questions quickly, and always goes the extra mile to help — they’re more like partners than just a supplier.
⭐⭐⭐⭐⭐
We trust LabChoice Australia because they deliver every time. Their borosilicate glassware is durable, accurate, and perfect for the high-heat work we do. Everything arrives well-packed with clear specs, so there are never surprises. It’s reassuring to deal with a supplier who understands both compliance and the demands of a busy lab