Very Low Frequency Oscillator, Sine Generator
AUD 174.50(Ex GST)
AUD 174.50(Ex GST)
- Very low frequency oscillator for laboratory and educational use
- IEC oscillator as listed
- Provides 0.1 Hz sine wave output
- One full sine wave cycle takes 10 seconds
- Output listed as 15 V peak-to-peak
- Output current listed as up to 5 mA
- Frequency accuracy listed as approximately ±5%
- Press button stops oscillation and holds output at 7.5 V
- Synchronisation feature helps align output with an event
- Useful for phase demonstrations in inductors
- Can demonstrate bridge rectifier operation in slow motion using LEDs
- Use under appropriate laboratory or educational supervision
[request_quote_button]
- Description
- Datasheets & Manuals
Description
The Very Low Frequency Oscillator, Sine Generator, also known as a low-frequency sine wave oscillator or classroom AC waveform generator, is designed for slow AC waveform demonstrations in physics and electronics teaching. The IEC Very Low Frequency Oscillator provides a 0.1 Hz sine wave output, meaning one complete sine wave cycle takes 10 seconds. This very slow waveform makes voltage changes easier to observe during classroom demonstrations. The output is listed as 15 V peak-to-peak, with output current up to 5 mA, making it suitable for compatible low-current educational circuits.
The frequency accuracy is listed as approximately ±5%, supporting practical demonstration rather than precision calibration work. A press button can stop the oscillation and hold the output at 7.5 V. This feature allows the oscillator output to be synchronised with a classroom event or experiment stage. The oscillator can be used for studying the phase relationship between voltage and current in inductors, and with compatible LEDs it can demonstrate bridge rectifier operation in slow motion.
Users should confirm connected circuit compatibility, load current, LED resistor requirements, oscilloscope or meter setup, and experiment procedure before use. Do not exceed the listed output current or connect the oscillator to mains circuits, high-voltage systems or unsuitable external power sources. As with all electrical teaching apparatus, circuits should be assembled with power off, checked before operation and used only with approved classroom components.
This product is intended for laboratory or educational settings only and should be used under appropriate supervision. This item is supplied as the selected very low frequency oscillator only. LEDs, bridge rectifier, resistors, inductors, meters, oscilloscope, connecting leads, worksheets, PPE and additional electronics accessories are not included unless specified separately.
LabChoice Australia supplies Very Low Frequency Oscillators and electronics teaching equipment for school science laboratories, university teaching laboratories, trade training facilities and educational environments requiring practical demonstrations of slow AC waveforms and circuit behaviour.
Datasheets & Manuals
Document :
Product Information Sheet(Pdf)
In-Line Mini DC Voltmeter, ±25 V Digital Meter
AUD 124.50(Ex GST)
Bibulous Paper Sheets for Drying Microscope Slides
AUD 31.50(Ex GST)
Liebig Condenser with Interchangeable Joint Socket, Borosilicate Glass (BORO 3.3)
From AUD 32.90 (Ex GST)
Adam Luna LPB Precision Balances for Precision Lab Weighing
From AUD 1,695.00 (Ex GST)
Polypropylene Carboys with Caps, Sterile - Each
From AUD 196.50 (Ex GST)
LCD Digital Magnetic Stirrer, Round Plate 5 Inch, up to 20 L Capacity
AUD 837.50(Ex GST)
Buchi Rotavapor Evaporating Flask, BORO 3.3
From AUD 18.90 (Ex GST)
You May Also Need
AC Theory Electricity Kit with Signal Generator
AUD 1,262.90(Ex GST)
Adjustable Aepinus Air Capacitor for Electrical Experiments
AUD 323.50(Ex GST)
Air-Cored Copper Solenoid for Magnetic Field Experiments
AUD 165.90(Ex GST)
ASEP Circuits Kit with Wire Card, Lamps and Clips
AUD 64.90(Ex GST)
Dissectible Transformer Complete Kit with Spot Welder
AUD 1,043.50(Ex GST)
Electronics Digital Trainer with Experiment Manual
AUD 380.90(Ex GST)
Hall Effect Kit with Constant Current Supply and Probe
AUD 982.50(Ex GST)
Key Press Contact Switch, Silver-Plated Contact Points
AUD 28.90(Ex GST)
Laboratory Electroscope in Metal Housing
From AUD 85.90 (Ex GST)
Large Audio Amplifier, Built-In Speaker for Physics Experiments
AUD 246.50(Ex GST)
Mass of Electron Apparatus with Tube, Without Solenoid
AUD 232.90(Ex GST)
Moulded Helmholtz Coil Pair, With Feet and Ruler Included
AUD 226.90(Ex GST)
Small Current Balance Kit, PSSC, Without Solenoid
AUD 83.50(Ex GST)
Small Motor and Generator Kit with Pulley, ASEP
AUD 72.50(Ex GST)
Universal Bench Clamp, Alloy, for Laboratory Rods
AUD 34.90(Ex GST)
[porto_related_products_slider]
Recently Viewed Products
SELECT OPTIONS
Boiling Flask, Flat Bottom, Borosilicate Glass (BORO 3.3)
From AUD 2.30 (Ex GST)
SELECT OPTIONS
Vernier Calipers For Laboratory and Educational Work
From AUD 9.90 (Ex GST)
SELECT OPTIONS
Straight Vacuum Adapter BORO 3.3 Glass Laboratory Grade
From AUD 28.50 (Ex GST)
FEATURED PRODUCTS
BEST SELLING PRODUCTS
Petri Dishes, Polypropylene, Autoclavable & Reusable, High Quality
From AUD 1.20 (Ex GST)
Stirring Rods, Rounded Ends, Laboratory Grade, Borosilicate Glass (BORO 3.3)
From AUD 0.95 (Ex GST)
Glass Petri Dishes with Lid, Autoclavable, Borosilicate Glass (BORO 3.3)
From AUD 3.90 (Ex GST)
TOP RATED PRODUCTS
What Our Customers Say
⭐⭐⭐⭐⭐
We ordered a set of customised BORO 3.3 borosilicate glassware for our teaching labs, and LabChoice Australia exceeded every expectation. From the first consultation to final delivery, their team listened carefully, offered expert advice, and ensured every piece matched our specifications perfectly.
The clarity and precision of the glassware are exceptional, and the quick turnaround made setup effortless. It’s refreshing to work with an Australian supplier who genuinely understands laboratory needs and takes pride in quality craftsmanship. We’ll definitely be returning to LabChoice for future glassware requirements
⭐⭐⭐⭐⭐
Our lab required high-precision BORO 3.3 glassware for analytical testing, and LabChoice Australia delivered outstanding results. The ordering process was simple, communication was clear, and every beaker and flask arrived perfectly calibrated and ready for use.
The quality of the glass is exceptional — resistant to heat, easy to clean, and consistently accurate in measurement. It’s reassuring to know there’s an Australian supplier that combines scientific precision with genuine customer care. I’d recommend LabChoice to any research team looking for dependable labware
⭐⭐⭐⭐⭐
We needed a set of customised borosilicate glassware for a specialised project, and LabChoice Australia delivered exactly what we envisioned. The team worked closely with us from design to production, ensuring every detail met our specifications. The craftsmanship is exceptional, and the turnaround time was impressive. It’s reassuring to know we can rely on them for unique, made-to-order pieces
⭐⭐⭐⭐⭐
LabChoice Australia has completely changed the way we source our lab glassware. The quality is consistently top-notch, and every piece meets the precision we need for reliable results. Their team knows their stuff, answers our questions quickly, and always goes the extra mile to help — they’re more like partners than just a supplier.
⭐⭐⭐⭐⭐
We trust LabChoice Australia because they deliver every time. Their borosilicate glassware is durable, accurate, and perfect for the high-heat work we do. Everything arrives well-packed with clear specs, so there are never surprises. It’s reassuring to deal with a supplier who understands both compliance and the demands of a busy lab