E
x
p
l
o
r
e
M
o
r
e
:
Electrochemistry Meters & Analysers
Handheld pH Meter Tester Kit for Strong Acid and Hydrofluoric Acid Solutions with LabSen 835 ATC Electrode, -2.00 to 16.00 pH
AUD 498.00(Ex GST)
AUD 498.00(Ex GST)
- Handheld pH meter tester kit for strong acidic and HF-containing water solution workflows
- Supplied with LabSen 835 ATC pH / temperature electrode for specialised acid sample testing
- HF-resistant membrane is designed to resist hydrofluoric corrosion and reduce acidic error
- Listed for up to 1000 HF measurements under specified conditions: less than 1 minute measurement time and HF concentration below 0.1 mol/L or 2000 ppm
- Silver Ion Trap reference system with open junction and polymer electrolyte supports long-term reference stability
- Intelligent meter functions include automatic calibration, ATC, reading alarm settings and automatic reading lock
- Complete kit includes User Manual, LabSen 835 pH Electrode, PH60 Meter Body, CalPod Solution Organizer, pH 1.68 Solution, pH 7.00 Solution, pH 10.01 Solution, 3M Soaking KCL Solution and Protective Cap
[request_quote_button]
- Description
- Datasheets & Manuals
Description
Handheld pH Meter Tester Kit for Strong Acid and Hydrofluoric Acid Solutions with LabSen 835 ATC Electrode, -2.00 to 16.00 pH, also known as a portable pH tester kit for acidic and HF-containing samples, is designed for users who need specialised pH measurement outside a fixed benchtop setup. This kit is suitable for laboratories, field technicians, water-quality users, research teams and quality-control environments where challenging acidic samples need to be checked with a portable meter and a suitable specialised electrode.
The meter and electrode combination supports practical on-site measurement where portability, calibration convenience and sample-specific electrode selection are important. It is useful for workflows where a standard pH electrode may not be suitable for aggressive acidic sample conditions.
Included with this pH Tester Kit: User Manual, LabSen 835 pH Electrode, PH60 Meter Body, CalPod Solution Organizer, pH 1.68 Solution, pH 7.00 Solution, pH 10.01 Solution, 3M Soaking KCL Solution and Protective Cap.
Important Safety Note: Hydrofluoric acid is highly hazardous. Users must confirm the permitted HF concentration, exposure time, PPE, laboratory safety procedure, neutralisation method and disposal requirements before using this electrode with HF-containing samples.
LabChoice Australia supplies Handheld pH Meter Tester Kits for water-quality professionals, schools, universities, research laboratories and testing facilities requiring portable pH measurement for strong acid, hydrofluoric acid-containing and general water solution applications.
Features
- Professional handheld pH tester kit
- Suitable for strong acid water solutions
- Suitable for hydrofluoric acid-containing solutions under specified conditions
- Also suitable for general water solution measurement
- Includes LabSen 835 pH / temperature electrode
- ATC electrode configuration
- pH range listed as -2.00 to 16.00 pH
- Swiss sensor technology referenced in supplied product information
- Specialised HF membrane
- Designed to minimise acidic error
- Silver Ion Trap reference system
- Open junction design
- Polymer electrolyte reference system
- Helps reduce junction clogging compared with ordinary electrode formats
- Water-resistant meter body
- Automatic calibration function
- Automatic temperature compensation
- Reading alarm settings
- Automatic reading lock function
- Calibration buffers and soaking solution referenced in supplied product information
- Apera CalPod Solution Organiser referenced in supplied product information
- Rugged carrying case included
- HF concentration, exposure time, safety procedure, calibration sequence and electrode care should be confirmed before use
Warranty
The instrument is covered for defects in material and workmanship for two years, while the probe is covered for six months from delivery, subject to the manufacturer’s warranty terms.
The limited warranty does not cover issues caused by accidental damage, improper use, normal wear and tear, transport, storage, failure to follow product instructions, unauthorised maintenance, unauthorised modification, unauthorised repair, incompatible use with other products or materials, abuse, accidents or external causes beyond reasonable control.
| Specification | Details |
|---|---|
| pH – Range | -2.00 – 16.00 pH |
| pH – Resolution | 0.01 pH |
| pH – Accuracy | ±0.01 pH ±1 digit |
| pH – Temperature Compensation | 0 to 100°C (Auto or Manual) |
| mV – Range | -1000 mV – 0 – 1000 mV |
| mV – Resolution | 1 mV |
| mV – Accuracy | ±0.2% F.S |
| Temp. – Range | 0 to 100°C (23 to 212°F) |
| Temp. – Resolution | 0.1°C |
| Temp. – Accuracy | ±0.5°C ±1 digit |
| Calibration | Auto. 1–3 points |
| Buffer Recognition | USA: pH 1.68, 4.00, 7.00,10.01, 12.45; NIST: pH 1.68, 4.01, 6.86, 9.18, 12.45 |
| Reading Alarm | Yes |
| Reading Auto. Hold | Yes |
| Temperature Unit | ˚C or ˚F |
| Screen Backlight | 3-color backlight with auto. power off: White – measurement mode Green – calibration mode Red – reading alarm |
| Self-diagnosis | Yes |
| Power | AAA Batteries * 4 |
| IP Rating | IP67 |
| Dimensions& Weight | Tester: 40×40×178mm/133g; Case: 255×210×50mm/700g; |
| pH Electrode Technical Specs (LabSen 845) | |
| Membrane Type | HF |
| Housing Material | Lead-free glass |
| Temperature sensor | 30KΩ NTC |
| Junction | Open |
| Reference Electrode | Silver Ion Trap Reference System |
| Electrolyte | Polymer |
| Range | 0 to 12 pH |
| Temperature Range | 0 to 100°C |
| Connector | 8-pin |
Datasheets & Manuals
Document :
Product Information Sheet(Pdf)
IEC Hot Plate Water Bath (Bath Only)
AUD 323.50(Ex GST)
Hand Held Cylinder Microtome with Razor and Glass Plates
AUD 117.50(Ex GST)
Test Tube Racks, Polypropylene 40 Holes for 20 mm Tubes Laboratory Type
From AUD 8.90 (Ex GST)
USB Temperature Sensor SUGU-T, -40°C to 125°C
AUD 184.00(Ex GST)
Triangular Prisms, Acrylic and Glass Optics Experiment Type
From AUD 6.50 (Ex GST)
Air Table Circular Magnet for Small Puck
AUD 12.50(Ex GST)
Microcentrifuge Tube, Polypropylene, Non - Sterile
From AUD 308.50 (Ex GST)
Centrifuge Tube with Flat Cap, Non-Sterile - Pack of 500 Tubes
From AUD 180.50 (Ex GST)
You May Also Need
Save 10%
Benchtop Classical Series Multi-Parameter Meter for pH, Conductivity and DO Testing
From AUD 2,467.50 (Ex GST)
Calcium Ion Sensor, Replacement Sensor with 0.1 to 5.0 mmol/L Range
AUD 528.00(Ex GST)
Conductivity Sensor, 0 µS/cm to 199.9 mS/cm Measurement Range
AUD 143.00(Ex GST)
Fluoride Sensor, Replacement Sensor with 0.3 mL Direct Measurement
AUD 227.70(Ex GST)
Multi Function Soil Meters with Stem Probes
From AUD 24.90 (Ex GST)
Pocket Ionized Calcium Meter, Cow Side Blood Testing with 0.3 mL Sample Volume
AUD 2,183.50(Ex GST)
Save 10%
Pocket Testers for Portable Water Quality Testing
From AUD 290.50 (Ex GST)
Save 10%
Pocket Testers with Bluetooth for Portable pH, ORP and Water Testing
From AUD 397.50 (Ex GST)
Pocket Water Quality Meter, Single-Drop On-Site Testing
AUD 330.00(Ex GST)
Potassium Ion Sensor, Replacement Sensor with 4 to 9900 ppm Range
AUD 227.70(Ex GST)
Salt EC Sensor, 0.12 mL Sample Testing with Ti/Pt Black Cell
AUD 143.00(Ex GST)
Sodium Ion Electrode, Replacement Sensor with 2 to 9900 ppm Range
AUD 227.70(Ex GST)
[porto_related_products_slider]
FEATURED PRODUCTS
BEST SELLING PRODUCTS
Petri Dishes, Polypropylene, Autoclavable & Reusable, High Quality
From AUD 1.20 (Ex GST)
Glass Petri Dishes with Lid, Autoclavable, Borosilicate Glass (BORO 3.3)
From AUD 3.90 (Ex GST)
Reagent Bottles, Wide Mouth, HDPE, Chemical-Resistant, Highly Reliable & Durable - Each
From AUD 1.50 (Ex GST)
LATEST PRODUCTS
TOP RATED PRODUCTS
What Our Customers Say
⭐⭐⭐⭐⭐
We ordered a set of customised BORO 3.3 borosilicate glassware for our teaching labs, and LabChoice Australia exceeded every expectation. From the first consultation to final delivery, their team listened carefully, offered expert advice, and ensured every piece matched our specifications perfectly.
The clarity and precision of the glassware are exceptional, and the quick turnaround made setup effortless. It’s refreshing to work with an Australian supplier who genuinely understands laboratory needs and takes pride in quality craftsmanship. We’ll definitely be returning to LabChoice for future glassware requirements
⭐⭐⭐⭐⭐
Our lab required high-precision BORO 3.3 glassware for analytical testing, and LabChoice Australia delivered outstanding results. The ordering process was simple, communication was clear, and every beaker and flask arrived perfectly calibrated and ready for use.
The quality of the glass is exceptional — resistant to heat, easy to clean, and consistently accurate in measurement. It’s reassuring to know there’s an Australian supplier that combines scientific precision with genuine customer care. I’d recommend LabChoice to any research team looking for dependable labware
⭐⭐⭐⭐⭐
We needed a set of customised borosilicate glassware for a specialised project, and LabChoice Australia delivered exactly what we envisioned. The team worked closely with us from design to production, ensuring every detail met our specifications. The craftsmanship is exceptional, and the turnaround time was impressive. It’s reassuring to know we can rely on them for unique, made-to-order pieces
⭐⭐⭐⭐⭐
LabChoice Australia has completely changed the way we source our lab glassware. The quality is consistently top-notch, and every piece meets the precision we need for reliable results. Their team knows their stuff, answers our questions quickly, and always goes the extra mile to help — they’re more like partners than just a supplier.
⭐⭐⭐⭐⭐
We trust LabChoice Australia because they deliver every time. Their borosilicate glassware is durable, accurate, and perfect for the high-heat work we do. Everything arrives well-packed with clear specs, so there are never surprises. It’s reassuring to deal with a supplier who understands both compliance and the demands of a busy lab